Pocket AL I/O QBUser’s Guiderev. 1.0 01/2013Alarm System via SMS 850/900/1800/1900MHz Quad-Band GSM Module Remote control of sensors Configu
2.2Pocket AL I/O QB QB InstallationNon optoinsulated Digital InputsTwo status are supported for each non optoinsulated input: open or closed to groun
2.3Pocket AL I/O QB QB InstallationOptoinsulated digital inputsIn case you use optoinsulated inputs, it will be necessary to use an external power vo
2.4Pocket AL I/O QB QB Installation2.1.4. Connection of external antennaOnce the inputs installation is over you can go on with the connection of th
2.5Pocket AL I/O QB QB Installation2.1.7. Powering on for the first time• OncethehardwareinstallationisoveritisnecessarytocongurePocket
3.1Pocket AL I/O QB Configuration3. CONFIGURATIONPocket AL I/O QB is setup with simple configuration commands through the RS232 serial interface (termi
3.2Pocket AL I/O QB Configuration3.1. DESCRIPTION OF CONFIGURATION MESSAGESThe commands here described can be sent both via serial port (terminal emul
3.3Pocket AL I/O QB Configuration3.3. STARTING CONFIGURATION3.3.1. Authorized users configurationIt defines the list of users authorized to set the dev
3.4Pocket AL I/O QB Configuration3.3.4. Configuration testTo test the configuration, send this message to Pocket AL I/O QB:#CONFIG#Pocket AL I/O QB wil
3.5Pocket AL I/O QB Configuration3.3.5. Search for GSM networkThe user can verify the operator used by the GSM module and the signal quality by sendi
3.6Pocket AL I/O QB Configuration3.4. DIGITAL INPUTS CONFIGURATIONFor the inputs configuration you must assign:• Analarmmnemonicname• Thetypeof
3.7Pocket AL I/O QB Configuration3.4.1. SMS Alarm MessagesThe message sent by the device in case of alarm to the devices set during the configuration
3.8Pocket AL I/O QB Configuration3.5.1. SMS alarm messages The message sent by the device in case of alarm to the devices set during the configuration
3.9Pocket AL I/O QB Configuration3.6.1. Outputs status modification (SMS messages)Pocket AL I/O QB outputs can be managed via SMS by authorized users
3.10Pocket AL I/O QB Configuration3.7. BACKUP BATTERY CONFIGURATIONPocket AL I/O QB has been designed to guarantee the operation even when power is of
3.11Pocket AL I/O QB ConfigurationExample of alarm messages of contact 15HOME15)MainPower ONBATTERY: CHARGINGHOME15)MainPower OFFBATTERY: LOW3.8. STAN
3.12Pocket AL I/O QB Configuration3.8.3. Standby confirmation messageThe enabling and disabling of STANDBY status must be confirmed with an SMS message
3.13Pocket AL I/O QB Configuration3.9. CONTACTS STATUS CHECKDuring the operation the user can require the contacts status at any time to Pocket AL I/O
4.1Pocket AL I/O QB Management through ring4. MANAGEMENT THROUGH RINGPocket AL I/O QB can be set to perform some actions when it receives a phone ri
IPocket AL I/O QB Index - PrefaceINDEXPREFACE ...
5.1Pocket AL I/O QB Pocket AL I/O QB Applications5. Pocket AL I/o QB APPLIcAtIoNSPocket AL I/O QB comes from Digicom know-how of PocketGSM AL and Ar
5.2Pocket AL I/O QB Pocket AL I/O QB Applications5.1.3. Particular managements1. AL standard application foresees the control of the alarm SMS numb
Warranty Clauses• Theproductisunderwarrantyforaperiodof24(twenty-four)monthsfromthedateofpurchase. Digicomundertakestoremedyany
Italy 21010 Cardano al Campo VAvia Alessandro Volta 39http://www.digicom.it
IIPocket AL I/O QB Index - PrefaceAll rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in
IIIPocket AL I/O QB Index - PrefaceSAFETY WARNINGSReadtheseinstructionsandnormscarefullybeforepoweringthedevice.Violationofsuchnormsmay
IVPocket AL I/O QB Index - PrefaceINFORMATION FOR USERSAccordingtothe2002/95/CE,2002/96/CEand2003/108/CEDirectives,relativetoreductionint
1.1Pocket AL I/O QB Introduction1. INTRODUCTIONCongratulations for choosing Pocket AL I/O QB Digicom. Pocket AL I/O QB is a signalling system via S
2.1Pocket AL I/O QB QB Installation2. INSTALLATIONThe installation of Pocket AL I/O QB QB is extremely easy and fast. The configuration can be perform
Komentáře k této Příručce